1Installation and Servicingwww.glow-worm.co.uk Clearly SolarSystem WiringincludingFluroproSolar Control
104 Electrical Installation14213Hydraulic Plan 1SOLAR COLLECTORBOILERSOLAR COLLECTORCIRCUIT PUMPAUTO AIRSEPARATORMOTORISED2 PORT VALVEMOTORISED2 PORT
114 Electrical Installation14212Hydraulic Plan 2SOLAR COLLECTORBOILER FLOWFLOWHOTWATERCONNECTIONSOLAR COLLECTORSOLAR COLLECTORCIRCUIT PUMPAUTO AIRSEP
124 Electrical InstallationBoilerFlexicom hx / sx,Ultracom hxi / sxi,old hxi / sxi3rd party ov / sysUltracom hxi / sxiwith options boardWiring11 way
134 Electrical Installation14793Diagram 4.1FLUROCYL E NL3rd PARTYEXTERNALPROGRAMMERFOR CHCOMMON 230VMAINS TERMINALBLOCKROOMTHERMOSTATLor E NNOCLTERMI
1414794Diagram 4.24 Electrical InstallationFLUROCYL3rd PARTYEXTERNALPROGRAMMERFOR CHROOMTHERMOSTATLor E ENNOCLTERMINAL BLOCK RETURN PIPE FUSED AT 3A
15Diagram 4.34 Electrical Installation14795COMMON 230VMAINS TERMINALBLOCK230V~50HzMAINS SUPPLYLNEDoublepoleisolatorAT 16A230V~50HzMAINS SUPPLYLNEDoub
1614796Diagram 4.44 Electrical InstallationCOMMON 230VMAINS TERMINALBLOCK230V~50HzMAINS SUPPLYLNEDoublepoleisolatorAT 16A230V~50HzMAINS SUPPLYLNEDoub
1714797Diagram 4.54 Electrical InstallationCOMMON 230VMAINS TERMINALBLOCK230V~50HzMAINS SUPPLYLNEDoublepoleisolatorAT 16A230V~50HzMAINS SUPPLYLNEDoub
1814277Diagram 4.74 Electrical InstallationINSTALLER INTERFACE OPTIONS FOR GLOW-WORM BOILERS4 ON TERMINALBLOCKBOILER OPTIONS4 ON TERMINALBLOCK4 ON TE
19Diagram 5.1147225 CommissioningUser Control PanelDisplay overview Display symbolsTimer programs: Cylinder reheat Not usedOperating modes: Cylinde
2Customer Service: 01773 596510Technical Helpline: 01773 828300.General and Sales enquiries: Tel. 01773 824639 Fax: 01773 820569To register
20Installer menuAccess the installer menu by pressing the button for 3 seconds. Press the button for 3 seconds again to return to the operating men
21Display Turn the dial to adjust Setting range Factory settingNot used.20 - 90 °C60 °CNot used.5 – 12 K7 KNot used.1 – 10 K3 KPRIOCylinder with highe
22Display Turn the dial to adjust Setting range Factory settingCylinder reheat delay function0=deactivated; 1=activated0Solar gain modulation function
23Adjust the solar water heating target tem-perature setting Important: Set the solar water heating target temperature to the maxim
246 Service menuAccess the service menu by simultaneously pressing the button and button for approx. 3 seconds. All relays and sensors can be contr
25Display Relay check/sensor values Test procedureLow cylinder sensor value Not usedCollector sensor value (array 1)Collector sensor value (array 2 if
26Cylinder sensors, type NTC 2.7 KSensor valuesResistance value0 °C9191 Ohm5 °C 7064 Ohm10 °C 5214 Ohm20 °C3384 Ohm25 °C2692 Ohm30 °C2158 Ohm40 °C 141
27Error collector sensor (array 1)This error occurs if the there is a problem with the collector sensor, or if it is not connected.Error collector sen
28Because of our constant endeavour for improvement, details may vary slightly from those shown in these instructions.Glow-worm, Nottingham Road, Belp
3 CONTENTS DESCRIPTION SECTION PAGE Regulations 4Electrical Supply 4Testing and Certi
4RegulationsWhen installing and commissioning the system, the current version of regulations below shall be observed.The electrical installation must
5Intended use The Fluropro solar control is a temperature differential controller for solar DHW provision with a cylinder reheat programmer for a supp
62.1 Solar gainThe Fluropro solar control works on the principal of differential temperature control. The control always switches on the collector pum
73 Installation3.1 Contents of setsUsing Table1, verify the contents of the Fluropro solar control set.Item Quantity Components11Fluropro21Collector
814260Diagram 3.42302303 Installation14263Diagram 3.5• Lift up the control panel, see diagram 3.5.• Wire the controller according to the selected hyd
9Electrical SupplyThe product MUST be earthed.All system components shall be of an approved type and allwiring to current I.E.E. wiring regulations.Ex
Comments to this Manuals